This page collects resources, questions, and requests related to air sampling. Please edit the pa...
Public Lab is an open community which collaboratively develops accessible, open source, Do-It-Yourself technologies for investigating local environmental health and justice issues.
| 25 CURRENT | liz |
April 19, 2021 14:28
| over 3 years ago
This page collects resources, questions, and requests related to air sampling. Please edit the page to add information or resources. BackgroundAir sampling is a way to capture small amounts of air for laboratory testing. Most air sampling methods involve pulling whole air samples into a bag or container through a vacuum system. The bag or container can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade).
Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page.
Types of air samplesAir samples typically fall into one of five categories: indoor air, ambient air, stationary sources (for instance, a smokestack or factory), soil vapor, and mobile sources (traffic). Each type is regulated differently with different sampling methods depending on what you are looking for. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket SamplingThe bucket monitor is a low-cost, community-friendly air sampler that helps people measure toxic chemicals such as benzene and hydrogen sulfide in their air. It is an EPA-approved grab sampling method that is significantly less expensive than many other air grab systems such as the summa canister (Louisiana Bucket Brigade). What it tests: When paired with lab analysis, the bucket monitor can measure up to 101 air pollutants including dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. The bucket monitor wiki page contains full instructions on how to build and use a bucket monitor, instructional videos and stories from community partners who have used the bucket to advocate for healthier air, plus a community Q&A. Cost: The bucket itself costs around $100 each but they are re-useable. The lab testing costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400.
Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association
Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016.
Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" ( permalink) publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows.
More resources on canister sampling |
Revert | |
| 24 | liz |
April 19, 2021 14:25
| over 3 years ago
This page collects resources, questions, and requests related to air sampling. Please edit the page to add information or resources. BackgroundAir sampling is a way to capture small amounts of air for laboratory testing. Most air sampling methods involve pulling whole air samples into a bag or container through a vacuum system. The bag or container can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade).
Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page.
Types of air samplesAir samples typically fall into one of five categories: indoor air, ambient air, stationary sources (for instance, a smokestack or factory), soil vapor, and mobile sources (traffic). Each type is regulated differently with different sampling methods depending on what you are looking for. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket SamplingThe bucket monitor is a low-cost, community-friendly air sampler that helps people measure toxic chemicals such as benzene and hydrogen sulfide in their air. It is an EPA-approved grab sampling method that is significantly less expensive than many other air grab systems such as the summa canister (Louisiana Bucket Brigade). What it tests: When paired with lab analysis, the bucket monitor can measure up to 101 air pollutants including dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. The bucket monitor wiki page contains full instructions on how to build and use a bucket monitor, instructional videos and stories from community partners who have used the bucket to advocate for healthier air, plus a community Q&A. Cost: The bucket itself costs around $100 each but they are re-useable. The lab testing costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400.
Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association
Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016
Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows
More resources on canister sampling |
Revert | |
| 23 | bhamster |
December 15, 2020 22:32
| about 4 years ago
This page collects resources, questions, and requests related to air sampling. Please edit the page to add information or resources. BackgroundAir sampling is a way to capture small amounts of air for laboratory testing. Most air sampling methods involve pulling whole air samples into a bag or container through a vacuum system. The bag or container can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade).
Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page.
Types of air samplesAir samples typically fall into one of five categories: indoor air, ambient air, stationary sources (for instance, a smokestack or factory), soil vapor, and mobile sources (traffic). Each type is regulated differently with different sampling methods depending on what you are looking for. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket SamplingThe bucket monitor is a low-cost, community-friendly air sampler that helps people measure toxic chemicals such as benzene and hydrogen sulfide in their air. It is an EPA-approved grab sampling method that is significantly less expensive than many other air grab systems such as the summa canister (Louisiana Bucket Brigade). What it tests: When paired with lab analysis, the bucket monitor can measure up to 101 air pollutants including dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. The bucket monitor wiki page contains full instructions on how to build and use a bucket monitor, instructional videos and stories from community partners who have used the bucket to advocate for healthier air, plus a community Q&A. Cost: The bucket itself costs around $100 each but they are re-useable. The lab testing costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400.
Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association
Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016
Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows
More resources on canister sampling |
Revert | |
| 22 | kgradow1 |
May 29, 2020 19:45
| over 4 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page. Types of air samplesAir samples typically fall into one of five categories: indoor air, ambient air, stationary sources (for instance, a smokestack or factory), soil vapor, and mobile sources (traffic). Each type is regulated differently with different sampling methods depending on what you are looking for. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 21 | kgradow1 |
May 29, 2020 18:12
| over 4 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page. Types of air samplesAir samples are typically fall into one of five categories: indoor air, ambient air, stationary sources (for instance, a smokestack or factory), soil vapor, and mobile sources (traffic). Each type is regulated differently with different sampling methods depending on the site and what you are looking for. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 20 | warren |
February 16, 2018 21:48
| almost 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Particle sensingAir sampling for particulate matter or dust pollution is another type of air sampling. See information on particle sensing on this page. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 19 | warren |
February 16, 2018 21:47
| almost 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Also see information on Particle Sensing on this page. Activities[activities:air-sampling] Bucket Sampling"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 18 | stevie |
December 08, 2017 16:20
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. The Summa Canisters are described in EPA Method TO-15, and are commonly used for the collection of volatile organic compounds (VOCs) in ambient and indoor air. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 17 | stevie |
December 08, 2017 16:13
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 16 | stevie |
December 08, 2017 16:11
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. It can take grab samples intermittently, or over a period of time. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 Helium Diffusion SamplerHelium diffusion samplers are wearable devices that take samples to measure (VOCs) in ambient and indoor air. Community use case: In 2016, community members in Pavillon, Wyoming participated in a health and air sampling study. They had noticed an increase in health issues locally and were concerned about the pollution coming from the many nearby gas wells. In their exploration of VOCs, they used a FLIR gas camera, Minirea 3000 air monitoring device, an ambient air model, Aldehyde Badges, Summa Canisters and two wearable monitors: HDS (Helium Diffusion Sampler), and Sorbent Tubes. More information on their study, the results and about their community can be found in the "When the Wind Blows" publication by Elizabeth Crowe, Sharyle Patton, Deborah Thomas, and Beverley Thorpe. More information on this study and the groups involved can be found on the Coming Clean webpage here at http://comingcleaninc.org/wind-blows More resources on canister sampling:
|
Revert | |
| 15 | liz |
October 11, 2017 21:09
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 More resources on canister sampling:
|
Revert | |
| 14 | liz |
October 11, 2017 21:01
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 More resources on canister sampling:
|
Revert | |
| 13 | stevie |
October 11, 2017 19:44
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 More resources on canister sampling:
|
Revert | |
| 12 | stevie |
October 11, 2017 19:44
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Other types of canisters for samplingThe Summa CanisterThe Summa Canister is a commercially available sampling system. Community use case: The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 More resources on canister sampling: - http://www.restek.com/pdfs/EVTG1073A.pdf |
Revert | |
| 11 | stevie |
October 11, 2017 19:21
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (The Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Summa CanisterThe Summa Canister is a commercially available sampling system. The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert | |
| 10 | stevie |
October 11, 2017 19:20
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (from the Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket:
Summa CanisterThe Summa Canister is a commercially available sampling system. The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert | |
| 9 | stevie |
October 11, 2017 19:20
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals (Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (from the Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket: - http://www.pbs.org/pov/fenceline/the-bucket-brigade/ - http://www.labucketbrigade.org/content/bucket Summa CanisterThe Summa Canister is a commercially available sampling system. The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert | |
| 8 | stevie |
October 11, 2017 19:19
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals( Louisiana Bucket Brigade). Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (from the Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket: - http://www.pbs.org/pov/fenceline/the-bucket-brigade/ - http://www.labucketbrigade.org/content/bucket Summa CanisterThe Summa Canister is a commercially available sampling system. The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert | |
| 7 | stevie |
October 11, 2017 19:14
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals Louisiana Bucket Brigade. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (from the Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket: - http://www.pbs.org/pov/fenceline/the-bucket-brigade/ - http://www.labucketbrigade.org/content/bucket Summa CanisterThe Summa Canister is a commercially available sampling system. The Citizens for a Healthy Community in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert | |
| 6 | stevie |
October 11, 2017 19:14
| about 7 years ago
This page collects resources, questions, requests related to air sampling, edit the page to add information or resources. BackgroundAir grab sampling is a way to capture air samples for laboratory testing. Most air grab sampling methods involve capturing air pulled into a bag through a vacuum system. The bag can then be sealed and shipped to a lab for testing. Air grab samples can be tested for over 100 different chemicals Louisiana Bucket Brigade. Questions[questions:air-sampling] Activities[activities:air-sampling] Bucket Sampling:"The Bucket is a patented device for capturing a sample of air for laboratory analysis in three minutes" from Blue Ridge Environmental Defence League. The Bucket is an EPA approved grab sampling method for measuring air pollution and is significantly less expensive than the other air grab systems such as the summa canister (from the Louisiana Bucket Brigade). What it tests: The Bucket can measure up to 101 air pollutants including: dichloromethane, hydrogen sulfide, perchloroethylene, vinyl chloride, toluene, and benzene. Written instructions and information on how to use the bucket can be found here from the Blue Ridge Environmental Defense League Cost: The bucket itself cost around $100 each but they are reuseable. The lab sampling costs between $200-$500 each depending on what you want to get tested. The system also needs to be calibrated twice a year which can cost up to $400. Video on how to use the bucket from Hilton Kelley of Community In Power and Development Association Story of West Virginia Chemical Valley Bucket Brigade: More resources and groups who have experience with the Bucket: - http://www.pbs.org/pov/fenceline/the-bucket-brigade/ - http://www.labucketbrigade.org/content/bucket Summa CanisterThe Summa Canister is a commercially available sampling system. The [Citizens for a Healthy Community] in Paonia, Colorado have used the summa canister for air grab sampling. Here is a publication they put together on “How Oil & Gas Impacted Communities Can Test Air Quality On A Small Budget: A step-by-step guidebook based on the North Fork Valley Air Sampling Program” 2016 |
Revert |