Kite mapping is similar to balloon mapping, but uses kites to lift cameras to take aerial photogr...
Public Lab is an open community which collaboratively develops accessible, open source, Do-It-Yourself technologies for investigating local environmental health and justice issues.
21 CURRENT | tahnok |
April 25, 2019 01:10
| over 5 years ago
Kite mapping is similar to balloon mapping, but uses kites to lift cameras to take aerial photographs. With kites and a 5-20 mph wind, many of the objectives of balloon mapping are possible without helium or balloons. If you want to map a site with consistent winds, you may be in luck! Kite Aerial Photography has a large and active community of practitioners which is focused on high-performance kites that can lift large loads and/or fly in very light winds. Here, we're especially focused on We sell a kite mapping pack with two kites and a lot of tails to help you get going. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. Activities[activities:kite-mapping] Questions[questions:kite-mapping] Choosing a kiteCommercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. Kite MakingMaking your own kite is great -- designs can range from easy and quick to bigger more ambitious one that can be more portable, stronger lifters, or light-wind flyers. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
20 | warren |
July 27, 2018 19:50
| over 6 years ago
Kite mapping is similar to balloon mapping, but uses kites to lift cameras to take aerial photographs. With kites and a 5-20 mph wind, many of the objectives of balloon mapping are possible without helium or balloons. If you want to map a site with consistent winds, you may be in luck! Kite Aerial Photography has a large and active community of practitioners which is focused on high-performance kites that can lift large loads and/or fly in very light winds. Here, we're especially focused on We sell a kite mapping pack with two kites and a lot of tails to help you get going. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. Activities[activities:kite-mapping] Questions[questions:kite-mapping] Choosing a kiteCommercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. Kite MakingMaking your own kite is great -- designs can range from easy and quick to bigger more ambitious one that can be more portable, stronger lifters, or light-wind flyers. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
19 | warren |
November 05, 2017 17:59
| about 7 years ago
Kite mapping is similar to balloon mapping, but uses kites to lift cameras to take aerial photographs. With kites and a 5-20 mph wind, many of the objectives of balloon mapping are possible without helium or balloons. If you want to map a site with consistent winds, you may be in luck! Kite Aerial Photography has a large and active community of practitioners which is focused on high-performance kites that can lift large loads and/or fly in very light winds. Here, we're especially focused on We sell a kite mapping pack with two kites and a lot of tails to help you get going. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. Activities[activities:kite-mapping] Questions[questions:kite-mapping] Choosing a kiteCommercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. Kite MakingMaking your own kite is great -- designs can range from easy and quick to bigger more ambitious one that can be more portable, stronger lifters, or light-wind flyers. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
18 | warren |
November 05, 2017 17:45
| about 7 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. We sell a kite mapping pack with two kites and a lot of tails to help you get going. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. Kite MakingMaking your own kite is great -- designs can range from easy and quick to bigger more ambitious one that can be more portable, stronger lifters, or light-wind flyers. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
17 | mathew |
July 01, 2013 16:45
| over 11 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. We sell a kite mapping pack with two kites and a lot of tails to help you get going. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
16 | mathew |
July 01, 2013 16:36
| over 11 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. We sell two kites and a 15' Fuzzy Tail for high-wind flying, together as our Kite Mapping Pack: 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
15 | mathew |
January 25, 2013 02:48
| almost 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that going downwind will drop the speed of your kite. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
14 | mathew |
January 25, 2013 00:45
| almost 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. 7ft. High Sky Delta is only $30 and a great complement to the Dazzle Delta, providing easier flying in high winds. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Also available in 7 and 11 foot versions for high and low winds. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, very light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy in strong winter winds. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
13 | mathew |
September 20, 2012 20:18
| about 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. See Olivia's excellent notes on selecting kite flying sites in an urban area. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
12 | mathew |
September 20, 2012 20:13
| about 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, and not great in light winds, but once it's in the air it's a stable flyer. A favorite of the Gowanus Conservancy. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
11 | mathew |
September 20, 2012 20:12
| about 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. 9ft. Dazzle Delta is only $46 and a very good, easy flier. It doesn't pack down very small, but is a very affordable and high quality light wind kite. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
10 | mathew |
September 20, 2012 20:09
| about 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. DIY Kitesto see the latest research notes on DIY kites, see the tag DIY kite. Delta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
9 | mathew |
September 20, 2012 20:07
| about 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. DIY KitesDelta kites are a quick build, and very effectiveMathew has step by step instructions as well as a spreadsheet of dimensions for a quick-to-build DIY Delta Kite. This is a proven design that flies well. He uses tvvek and bamboo, but wooden dowels and plastic sheeting will work as well. Astoicof wrote great build notes and a PDF on using plastic sheeting to make a delta kite.. Jeff Warren and kids at Parts and Crafts have gotten good results from a mylar copy of the Dazzle Delta.. Safidy has been playing with NASA's Kite Modeler software and making DIY deltas. Non-DeltasGrassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew also made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. Leo Famulari has notes on kite bridle adjustment Other Kite Building ResourcesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
8 | mathew |
June 16, 2012 01:21
| over 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesKiteplans.org and the Kitebuilder forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Grassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. If you copy this kite, give it a tail. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
7 | mathew |
June 16, 2012 01:20
| over 12 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Levitation Delta - ($65) 9 ft. wide - a strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds (7mph). Not as much lift as the Levitation and it doesn't break down as small, but it is much easier to handle in high winds. A great all-around kite. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesKiteplans.org and the Kitebuilder(http://kitebuilder.com) forums are great online resources. The book One-hour Kites by Jim Rowlands provides excellent plans and construction details. Dan Kurahashi's Japanese Kites, Concepts and Construction has more great plans, great charts on predicting lift, and some excellent instructions on making plastic bag kites. Grassroots Mappers in Peru have had good luck with plastic and bamboo kites. Mathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. If you copy this kite, give it a tail. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
6 | mathew |
February 17, 2012 20:19
| almost 13 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites, and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the PET Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds. I'd recommend this to anyone. Levitation Delta - ($65) 9 ft. wide - another strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesMathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
5 | liz |
January 31, 2012 22:27
| almost 13 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites, and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the Soda Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds. I'd recommend this to anyone. Levitation Delta - ($65) 9 ft. wide - another strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesMathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
4 | liz |
January 31, 2012 15:52
| almost 13 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites, and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the Soda Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds. I'd recommend this to anyone. Levitation Delta - ($65) 9 ft. wide - another strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesMathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. Published literature pertaining to KAPNathan Craig's Mendeley Group may require setting-up a free, public account. |
Revert | |
3 | mathew |
November 04, 2011 17:00
| about 13 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites, and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the Soda Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds. I'd recommend this to anyone. Levitation Delta - ($65) 9 ft. wide - another strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesMathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. There is also an easier to build Delta kite kit in development. See Mathew and Pat Coyle's work in progress. |
Revert | |
2 | ncraig |
November 03, 2011 15:59
| about 13 years ago
Kite Aerial Photography has a large and active community of practitioners -- see if there are any living or kiting near you, and ask for help. With kites, and a 5-20 mph wind, many of the objectives of balloon mapping can be achieved without purchasing helium or balloons. If you want to map a site with consistent winds, you may be in luck. Towing kitesKites can also be used in large flat areas with no power lines or trees, such as on oceans or lakes, beaches, or deserts, by towing them behind a boat, car, or bicycle. Keep in mind that it's typically impossible to turn or travel downwind. recommended commercial kitesKite Aerial Photographers, or KAPers, often select expensive kites which can lift large weights, and many use heavier, customizable cameras such as digital SLRs with remote control targeting or stabilization. If you just want to put a camera in the air for the lowest cost and highest reliability, we recommend a few different relatively inexpensive kites, paired with the Soda Bottle Rig. Fled - ($110) stable, strong, light-wind kite that flies at a line angle of 65 - 70 degrees. This kite is very quick to set up and simple to adjust. It flies in a wide range of conditions, and is a "go-to" kite for many KAPers. The high line angle is very useful for flying in tight spaces. Zenith Delta - ($70) 7 ft. wide - This one is fantastic, a strong and stable flyer in even light winds. I'd recommend this to anyone. Levitation Delta - ($65) 9 ft. wide - another strong and stable flyer in 7-20mph winds. In high winds it can take some effort to reel in, as it has a lot of lift. The spars all split in half and it packs down easily to 40." Good, high flying angle. Gomberg Delta Conyne - ($37) - Harder to launch, but once it's in the air it's a stable flyer. I think it's optimized for stable flight high up. Nice also that there's a space in the middle which we're going to try putting a camera in. Recommended DIY KitesMathew Lippincott has made a series of Tyvek and Bamboo Fled kites based on the designs of Brooks Leffler. The third has been extremely successful at lifting cameras to very high flying angles, and he can now recommend others to build the same. follow his instructions in the link above. |
Revert |