Question: What is "immersion oil" for microscopes?

warren is asking a question about microscopes
Follow this topic

by warren | February 16, 2018 15:25 | #15747


I've seen some microscopes use "immersion oil" -- like, an oil between the lens and the slide. What's this for and where can I find it? Do all microscopes need it? Can non-oil microscopes use oil or vice versa?



8 Comments

Lots of dense info on this here, but I'm not sure for a given lens if you can just add oil or not?

https://en.wikipedia.org/wiki/Oil_immersion

Is this a question? Click here to post it to the Questions page.

Reply to this comment...


@partsandcrafts -- is the oil absolutely required? Like, is it possible to skip this if you don't need the extra... awesomeness? @wmacfarl @kgradow1 @bmela

Is this a question? Click here to post it to the Questions page.

Reply to this comment...


Glass apparently has a refractive index of ~ 1.5 while air is 1.0. This means that light velocity is slower in glass. When light from a sample slide passes through air to objective lens there is refraction or bending of light away from perpendicular. As a result, some of the light from the specimen is lost and does not enter the aperature of the lens. If you fill the air gap between slide and lens with oil with a similar refractive index as the glass slide (i.e. 1.5) then the light is no longer refracted away from lens. With this effective increased light entering the lens or increase in aperature; resolution of detail in the sample is increased. Yes you can skip it if you have adequate resolution to see the detail in specimen your are interested in.

Wow, thanks! So how close is actually helpful? I found a list of household oils and refractive indices and mineral oil is around 1.47-1.48 -- would that help almost identically or would it be not a lot of help.

https://www.gemsociety.org/article/refractive-index-list-of-common-household-liquids/

Refractive Index List of Common Household Liquids Liquid Refractive Index alcohol, ethyl 1.36 almond oil 1.45-1.47 anise oil 1.54-1.56 Canadian balsam 1.53-1.55 cassia oil 1.58-1.60 castor oil 1.47-1.48 cedar wood oil 1.51 cinnamon oil 1.59-1.62 clove oil 1.53 coconut oil 1.43-1.46 cod liver oil 1.46-1.48 corn oil 1.47-1.48 cottonseed oil 1.45-1.48 eucalyptus oil 1.46-1.47 glycerol (glycerin oil) 1.47 kerosene 1.45 lanolin 1.48 lemon oil 1.47-1.48 linseed oil 1.47-1.49 mineral oil 1.47-1.48 neatsfoot oil 1.47 olive oil 1.44-1.47 palm oil 1.44-1.46 peppermint oil 1.46-1.47 rape seed oil 1.47-1.48 safflower oil 1.47-1.48 sandalwood oil 1.50-1.51 sesame oil 1.47 soybean oil 1.47-1.48 tung oil 1.49-1.52 turpentine 1.47 water 1.33 wintergreen oil 1.54 Editor’s Note: This list was compiled from information provided by Donald Clark, CSM IMG, Dr. Gerald Wykoff, Dr. Clive Washington, Roy Kersey, and others.

Is this a question? Click here to post it to the Questions page.


I do not know, but anything would be an improvement; just apply the oil (a bubble connecting slide through air to lens surface) and check the detail of objects in sample I assume. Arbitrarily anything above 1.4 would be pretty good. Amazing you found a list; surprising alcohol so high ?

Is this a question? Click here to post it to the Questions page.


Awesome, thanks! yes, alcohol is surprising!


Mineral oil should work. I sometimes use on a professional immersion objectives a mixture of drugstore-bought liquid paraffin (sold as a laxative) and sewing machine oil. Both are just highly purified mineral oil. Liquid paraffin is thicker than sewing machine oil, mixing them in 1:1 ratio gives just the right viscosity. The downside of using this mixture instead of a commercial immersion oil is that it's harder to clean. Cleaning objectives after each use is required in my lab, and getting rid of paraffin using microfibre cloth soaked in a bit of ethanol and diethyl ether is tedious as opposed to cleaning commercial immersion oils.


Wow, great info. Love this!


Reply to this comment...


Log in to comment