Revisions for Desktop Spectrometry Kit 3.0
| 76 | warren |
July 02, 2015 13:46
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
Also see this longer illustrated parts list. Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
BenchPut velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus. Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating, and the tiny webcam lens curves the spectrum anyways. Aligning your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and trimming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission, as described in this note. Peel apart a quarter of the DVDCut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Put velcro on the bottom.
Put the outer edge of the DVD at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxWatch this step-by step video: For the purposes of this instructional I've highlighted the edges of the box in white and used an unprinted box. Your box will have a printed and unprinted sides, and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. and crease the box top as well.
Fold the right side over to the left.
Lay the box top so its tabs line up with the slots in the box bottom’s right side. Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Put it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 75 | warren |
July 02, 2015 13:45
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
Also see this longer illustrated parts list. Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
BenchPut velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus. Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating, and the tiny webcam lens curves the spectrum anyways. Aligning your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and trimming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission, as described in this note. Peel apart a quarter of the DVDCut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Put velcro on the bottom.
Put the outer edge of the DVD at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxWatch this step-by step video: For the purposes of this instructional I've highlighted the edges of the box in white and used an unprinted box. Your box will have a printed and unprinted sides, and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. and crease the box top as well.
Fold the right side over to the left.
Lay the box top so its tabs line up with the slots in the box bottom’s right side. Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Put it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 74 | warren |
July 02, 2015 13:43
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
Also see this longer illustrated parts list. Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
BenchPut velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus. Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission, as described in this note. Peel apart a quarter of the DVDCut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Put velcro on the bottom.
Put the outer edge of the DVD at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxWatch this step-by step video: For the purposes of this instructional I've highlighted the edges of the box in white and used an unprinted box. Your box will have a printed and unprinted sides, and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. and crease the box top as well.
Fold the right side over to the left.
Lay the box top so its tabs line up with the slots in the box bottom’s right side. Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Put it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 73 | warren |
July 02, 2015 13:41
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
Also see this longer illustrated parts list. Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
BenchPut velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus. Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission, as described in this note. Peel apart a quarter of the DVDCut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Put velcro on the bottom.
Put the outer edge of the DVD at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxWatch this step-by step video: For the purposes of this instructional I've highlighted the edges of the box in white and used an unprinted box. Your box will have a printed and unprinted sides, and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. and crease the box top as well.
Fold the right side over to the left.
Lay the box top so its tabs line up with the slots in the box bottom’s right side. Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Put it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 72 | warren |
July 01, 2015 21:58
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 71 | warren |
July 01, 2015 21:57
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 70 | warren |
July 01, 2015 21:56
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple [5 question survey](#Survey) at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit.
Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and smartphones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
Complete!You're done! Your computer should recognize your spectrometer as a webcam. Now connect to your spectrometer using the web-based software at Spectralworkbench.org Resources
ActivitiesHere are the series of notes printed on the spectrometer. Notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
Spectrometer development: Activities:
Design NotesConsult the following notes on development for the evolution of this design: Survey |
Revert | ||||||||||||||
| 69 | warren |
June 26, 2015 19:00
| almost 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit. The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Formatted for booklet printing: Booklet Instructions Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ Survey |
Revert | ||||||||||||||
| 68 | natalie |
February 19, 2015 20:23
| about 9 years ago
Did you just purchase the new Desktop Spectrometer? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and the whole process better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit. The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Formatted for booklet printing: Booklet Instructions Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ Survey |
Revert | ||||||||||||||
| 67 | natalie |
February 19, 2015 20:22
| about 9 years ago
Did you just purchase a kit? Congratulations! You are one of the first 100 people to assemble this kit. We are excited to have you join us and highly value your feedback. In fact, we need it to make our instructions and kit better. Please take a minute to fill out a simple 5 question survey at the bottom of this page. Tell us about your experience assembling, finding and working with the instructions and using the kit. The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Formatted for booklet printing: Booklet Instructions Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ Survey |
Revert | ||||||||||||||
| 66 | mathew |
February 13, 2015 23:41
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Formatted for booklet printing: Booklet Instructions Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ |
Revert | ||||||||||||||
| 65 | mathew |
February 13, 2015 23:41
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Print this page as a PDF Formatted for booklet printing: Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ |
Revert | ||||||||||||||
| 64 | mathew |
February 13, 2015 23:36
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the loop tape (fuzzy side of the velcro).
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the hook tape (the Velcro's scratchy side).
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating, a device for separating light by frequency. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating. Aligningy your diffraction grating will take some tweaking. We’ve given you extra material to help.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cut out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. If you can’t find a good piece you may want to try another quarter DVD. You only need a 2cm (.75”) square cut from the outer edge. Trim down to a small square with roughly 2cm of the DVD’s outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
When taping the three flaps together, make sure the bottom flaps are lined up. put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. For the purposes of this instructional I’ve highlighted the edges of the box in white and used an unprinted box. your box will have a printed and unprinted sides and no white edges. Place the box with the printing facing down. Pre-crease all the creases towards you. crease the box top as well.
Fold the right side over to the left
Lay the box top so its tabs line up with the slots in the box bottom’s right side Make sure the small rectangular holes on the top and bottom of the box line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Now open the box back up and fold left and right side flaps to the middle to form the inner walls. They will hook together.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ |
Revert | ||||||||||||||
| 63 | mathew |
February 12, 2015 18:10
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
OPTIONAL: Make the camera focus more precise. The camera's tiny lens is pre-focused to roughly 200mm at the factory, but you can do a little better. This requires twisting the lens until it is no longer held in place by the green glue on the lens, which is easiest after the camera is mounted on the block. Pliers may be needed. Once loose, point the camera at a target (like text) 200mm away and carefully twisting the camera lens until the image is in clearest focus. See more research on lens focus: /n/7226 Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2****__ |
Revert | ||||||||||||||
| 62 | mathew |
February 12, 2015 18:02
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert | ||||||||||||||
| 61 | mathew |
February 12, 2015 17:53
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert | ||||||||||||||
| 60 | mathew |
February 12, 2015 17:47
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry. this is because there is extra space for the two sheets to fold together.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert | ||||||||||||||
| 59 | mathew |
February 12, 2015 04:21
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert | ||||||||||||||
| 58 | mathew |
February 12, 2015 04:19
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
click here to see a longer illustrated parts list.
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert | ||||||||||||||
| 57 | mathew |
February 12, 2015 02:13
| about 9 years ago
The Public Lab Desktop Spectrometry Kit 3.0 is the latest version of the spectrometer. Read more about our Spectrometry program, the Oil Testing Kit it is is a part of, or the history of development. Previous versions 2 & 2.5 are here. Parts List
Using your spectrometerOnce you've assembled your spectrometer and are ready to use it, plug it in and visit SpectralWorkbench.org to begin recording data with it. The web-based software works in the Chrome, Firefox and Opera browsers on most computers and Android phones. (Peer) SupportPublic Lab is not a corporation; we're an open community of DIY environmental science researchers which you have just joined! The best place to get help is the spectrometry mailing list; to join, sign up in the form to the left. The spectrometry mailing list is made up of people like you, who are building and improving open source spectrometry techniques. Ask questions, look for help, and consider helping others too! You can also post a question on this site; it helps to share some photos or screenshots of what you're trying to do: [question:spectrometry] Resources
Activitieshere are the series of notes printed on the spectrometer. notes below by: @amysoyka, @straylight, @wagnerc4, @ygzstc, @cfastie, @stoft, & @Alex-McCarthy.
This spectrometer design: Spectrometer development: Activities:
AssemblyYour spectrometer is composed of three functional elements:
These elements are mounted on an adjustable velcro bench in a black paper box.
Putting velcro on the benchEverything is built up from the bench, an ash board 4cm (1.75 inches) wide. We will cover it with the "loop" side of the velcro.
The velcro loop tape is slightly wider than half the width of the bench, two strips will hang over each edge a bit.
Assemble the camera blockYou will need the camera, double-sided tape, the block, and the hook side of the velcro tape. Try to hold the camera by its edges, as it can be sensitive to electrical shorts.
Start by putting a strip of double-sided tape on the back side of the camera:
Remove the pink protective film from the double-sided tape and attach to the center of the block's 45-degree angled side, with the white cable port on top:
On the underside of the block, attach two short strips of the velcro hook tape.
Make a diffraction grating from a DVDDo not touch the surface of the DVD, always hold it by the edges, fingerprints will blur this important optical component. We are going to turn a DVD-R into a diffraction grating. An ideal diffraction grating would create a straight rainbow. A DVD produces a curved rainbow, but its rigidity and consistency make it a very good grating.
We have three steps, cutting a quarter of the DVD out, peeling off the reflective aluminum side, and triming to a small piece.
OPTIONAL: Wash the purple ink off of the DVD fragment for greater light transmission. see note /n/11515. Peeling apart a quarter of the DVD:Cutting out a quarter of the DVD with scissors. It may take more than one try to get a good diffraction grating, so save the rest too. Use a knife or a fingernail to dig under the corner of the DVD quarter and peel the two layers apart.
You will get two layers. We are trying to get a transparent purple piece without aluminum stuck to it. Some may get stuck to the sides, but we only need a 2cm (.75") square cut from the outer edge.
Trim down to a small square with roughly 2cm of the DVD's outer edge.
Assemble the diffraction grating angleYou will need:
Overview:
Make sure the bottom flaps are lined up.
put hook tape on the bottom.
Put the outer edge of the dvd at the mid-point of the hole, and then remove the handles from the binder clip.
Assemble the slit cardYou will need:
The collimation slit should be in the DVD sleeve. _We will attach the slit using the tape as single sided tape-- tape it on top and DO NOT remove the backing film. _ Line up the collimation slit with the line on the slit card. Assemble the boxstep-by step video: For the purposes of this instructional I've highlighted the edges of the box. Place the box with the printing facing down. Pre-crease all the creases.
Fold the left side of the box to the right, and insert the hold tab in place.
Fold the right side to the left and lay the box top on top so its tabs line up with the slots in the box bottom. Make sure the small rectangular holes on the top and bottom line up. We will put the webcam cable through that hole later.
Insert the tabs together. The box top will not lay flat-- don't worry.
Pull the box top back to the right and fold the inner walls to the middle.
Hook the inner walls together.
Fold the outer walls up and over the inner walls. Use the two circular holes in the outer walls to position the inner walls while folding the outer wall over.
Flip the box upside down and make sure the tabs have all popped out of the bottom of the box. Walk your fingers along the inside of the box and make sure all the tabs are popped out of the bottom.
Putting it all on the bench
Line up the the bench with the side of the box, and align the camera's lens with the 200mm marker on the side of the box. Press the camera block down firmly. Place the diffraction grating angle directly in front of the camera block and press it down firmly.
Slide the slit card in the front of the box. The printing is slightly off, unfortunately. level the slit card's line just above the box's line. the card should wedge in place on its bottom edge.
Push the camera cable through the cable hole in the back of the box:
Plug it into the camera-- it only fits one way, don't force it.
Slide the bench in at an angle, placing it down by the cable hole, and then pushing it down to the bottom.
You're done! Your computer should recognize your spectrometer as a webcam. setup live capture for your spectrometer on Spectralworkbench.org Design Notesconsult the following notes on development for the evolution of this design. @mathew paper spectrometer 1, paper spectrometer 2 |
Revert |
