[![MakerBot.jpg](https://i.publiclab.org/system/images/photos/000/002/770/medium/MakerBot.jpg)](https://i.publiclab.org/system/images/photos/000/002/770/original/MakerBot.jpg)  

The status of [Public Lab's 10 MakerBot Replicators](http://publiclab.org/wiki/makerbot).

-  **Public Lab office**, Propeller Workspace, 4035 Washington Ave, New Orleans, LA 
    - Contact: Shannon Dosemagen

    1. SN______ on loan
       - Build hours:
       - Projects:
       - Maintenance:
    2. SN______ on loan
       - Build hours:
       - Projects:
       - Maintenance:
    3. SN _____  not operational  
       - Build hours:
       - Projects:
       - Maintenance:  
.  
  
- ** Picayune, MS**
    -  Contact:  Dan Beavers: danbeavers at organizers dot publiclab dot org
    - SN______ 
    - Build hours:
    - Projects:
    - Maintenance:
       - Arrived with both extruders upgraded to the spring loaded roller type (no delrin plungers).
       - Left extruder inoperable due to cable break that I just have not fixed yet.  
       - The 5 volt power upgrade has not been performed yet.  
.  
  
- **Geography Department, University of Kentucky**
    - Contact: Jessi Breen
    - SN______ not operational  
    - Build hours:
    - Projects:  
    - Maintenance:  
.  
  
-  **Public Lab office, Brooklyn, NY**, Former Pfizer building, 630 Flushing Avenue
    - Contact: Liz Barry
    - SN_____ not operational  
    - Build hours:
    - Projects:  
    - Maintenance:  
.  
  
-  **Parts and Crafts**, Sommerville, MA
    - Contact Katie and Will
    - SN_____ 
    - Build hours:  
    - Projects:
    - Maintenance:  
       - 
.  
  
- **Hackrfarm/University of Massachusetts**
    - Contact: Ian Walls
    - SN_______
    - Build hours:
    - Projects:
    - Maintenance:  
.  
  
- ** LEAFFEST HQ**, Salisbury, VT
  - Contact: Chris Fastie whose gmail is cfastie
  - SN 11837
  - Build hours:
       -  Initial build hours 12/2013: 11
       -  build hours on 02/07/2014: 245
       -  build hours on 08/18/2014: 640
       -  build hours on 01/01/2015: 1000  
       -  build hours on 02/08/2015: 1200  
[![1000hours-563-4.jpg](https://i.publiclab.org/system/images/photos/000/008/556/thumb/1000hours-563-4.jpg)](https://i.publiclab.org/system/images/photos/000/008/556/original/1000hours-563-4.jpg)  

  - Projects:
       - Prototyping camera rigs for aerial mapping
       - Experimenting with producing camera rigs for sale to Public Lab mappers
       - Prototyping spectrometer
  - Maintenance:   
[![UndExt-328-2.jpg](https://i.publiclab.org/system/images/photos/000/002/818/thumb/UndExt-328-2.jpg)](https://i.publiclab.org/system/images/photos/000/002/818/original/UndExt-328-2.jpg)  
  
    - tightened all hex bolts holding plywood frame together 12/2014
    - upgraded firmware to Makerbot v. 7.5
    - broken fan replaced 12/24/2013
    - new nozzles installed 01/04/2014
    - 24v/5v regulator replaced 01/17/2014
    - Removed left nozzle so it could not keep knocking over my prints. 01/20/2014
    - Filament feed mechanism upgraded (all prints were failing) (MakerBot replacement parts for right extruder) 02/06/2014
    - Filament feed mechanism for left extruder printed and installed with MakerBot hardware 04/2014
    - Printed feet, spool holders, and LCD/keypad cover  
    - lubricated noisy fan in motherboard compartment with SuperLube 06/2014
    - Replaced x-axis motor cable (all prints were failing) 08/18/2014
    - x-axis idler pulley is lubricated every week with SuperLube.
    - Installed new ball bearing x-axis idler pulley from Alm Gear ($18). 01/20/2015
    - Tightened all belts. 01/20/2015
    - Tightened all hex bolts holding plywood frame together. They were all loose again after 1000 hours of printing. 01/21/2015
    - Tightened both grub screws on all six pulleys. They all tightened, but I noticed no difference in performance. 01/29/2015
    - Removed the fan from the motherboard compartment. It is not needed for cooling (long story) and just makes noise. 02/11/2015  

.  


  
-  **Public Lab retail fulfillment center**, Portland, OR
   - Contact: Mathew Lippincott
   - SN 12328
   - Build hours:
   - Projects:
- 24v/5v regulator replaced 3/14
- spool holders replaced
- indicator LEDs disconnected to prevent voltage damage to board by motors.

   - Maintenance: